STM32F429ZIT6 vs STM32H753VIT6: A Parameter Comparison for Buyers
The STM32F429ZIT6 and the STM32H753VIT6 share a maker, a 2 MB flash, and a place on many of the same BOMs. They are not interchangeable. This comparison works through the parameters line by line, so you can see which differences are safe and which need an engineer to approve.
Home / News / STM32F429ZIT6 vs STM32H753VIT6: A Parameter Comparison for Buyers
November 2026
What Do the Part Numbers Tell You?
Both part numbers follow the same STMicroelectronics code, and each letter carries one fact. STM32 names the 32 bit Arm microcontroller family. F429 and H753 name the series and the line. The next letter decides this comparison. Z means 144 pins and V means 100 pins. I means 2 MB of flash. T means a temperature range of minus 40 to plus 85 degrees C. The final 6 means an LQFP package. The first difference is already visible: the same flash, the same temperature range, the same package family, but 44 fewer pins on the STM32H753VIT6.
Where Do the Two Parts Match?
The match list is short, and it is the reason buyers ask the question in the first place. Both parts carry 2 MB of flash in a dual bank layout with read while write, so code can be updated in one bank while the other keeps running. Both work from minus 40 to plus 85 degrees C, and both offer three ADCs and two 12 bit DACs, a USB OTG full speed and high speed interface, and an Ethernet MAC with a DMA controller. The flash match matters most: a design that fills 2 MB on the F429 does not run out of code space on the H753. Every other line moves, and the moves decide the approval.
Where Do the Two Parts Differ?
The table below takes the values from the two STMicroelectronics datasheets. Read it as a list of changes to approve, not as a scorecard: a faster core, more RAM, and a finer ADC all change the firmware, the power design, or the analog front end.
| Parameter | STM32F429ZIT6 | STM32H753VIT6 |
|---|---|---|
| Core | Cortex M4 with FPU | Cortex M7 with double precision FPU |
| Maximum clock | 180 MHz | 480 MHz |
| Performance | 225 DMIPS | 1027 DMIPS |
| RAM | 256 KB plus 4 KB backup | 1 MB, with 192 KB of TCM RAM |
| Flash | 2 MB | 2 MB with ECC |
| ADC | 3 ADCs, 12 bit, 24 channels | 3 ADCs, 16 bit maximum, 36 channels, 3.6 MSPS |
| DAC | 2 DACs, 12 bit | 2 DACs, 12 bit |
| CAN | 2 CAN 2.0B controllers | 2 CAN FD controllers |
| Timers | 17 timers | Up to 22 timers and watchdogs |
| Package | 144 pin LQFP, 20 mm by 20 mm | 100 pin LQFP, 14 mm by 14 mm |
| I/O pins | 114 | 100 pins in total |
| Supply | 1.7 V to 3.6 V | 1.62 V to 3.6 V |
| Extra hardware | LCD TFT controller, Chrom ART accelerator, camera interface | LCD TFT controller, Chrom ART accelerator, hardware JPEG codec, crypto acceleration, true random number generator, camera interface |
Three differences carry the most weight. First, the core moves from a Cortex M4 to a Cortex M7 with a double precision floating point unit and 16 KB instruction and data caches. Code written for the M4 needs a port, a new clock tree, a new memory map, and a new HAL. Second, the ADC moves from 12 bit to 16 bit maximum resolution. A 12 bit reading has 4096 steps and a 16 bit reading has 65536 steps, so every threshold, calibration value, and scaling factor in the analog path needs a recheck. Third, the CAN pair moves from CAN 2.0B to CAN FD. CAN FD frames carry more data than classic CAN frames, so every node on the bus must support the same protocol. A faster part does not fix a bus that disagrees.
Can the STM32H753VIT6 Replace the STM32F429ZIT6 on the Same Board?
No. The package decides this before any other parameter. The STM32F429ZIT6 sits in a 144 pin LQFP that measures 20 mm by 20 mm and offers 114 I/O pins. The STM32H753VIT6 sits in a 100 pin LQFP that measures 14 mm by 14 mm. A board built for 114 I/O pins cannot lose 44 pins, and the smaller package will not fit the larger footprint. The pinout differs too, so power, boot, and peripheral pins sit in different places. Even a fresh board layout would still need new firmware, because the core, clock tree, and memory map all change. For a buyer in a shortage, this pair is a redesign, not a substitution. When the board must stay unchanged, ask for the STM32H753ZIT6 instead, the same H7 core in a 144 pin LQFP. The footprint question then goes away, but the firmware and peripheral questions stay and still need an engineer to approve.
Which Differences Need an Engineer to Approve?
Five checks need a named engineer to sign off. First, the firmware port: core, floating point unit, cache, clock tree, and memory map all change from the M4 to the M7. Second, the analog path: ADC resolution, channel count, and every calibration value change with the move from 12 bit to 16 bit. Third, the CAN bus: CAN FD and CAN 2.0B are different protocols, and the bus owner must confirm every node agrees. Fourth, the board: package, pin count, and pinout change, so the layout, power pins, and decoupling must be redrawn. Fifth, the power supply: the H753 accepts a lower minimum supply of 1.62 V against 1.7 V on the F429, so a design near the lower edge must be rechecked against the datasheet current tables. None of these is a reason to refuse the change, but each needs approval in writing before the order is placed, with a sample on the bench first when the quantity is large.
What Should Your Enquiry Ask the Supplier?
Send the full part number with every suffix, and ask the supplier to confirm it letter by letter. A quote for the ZIT6 when you need the VIT6, or the reverse, is a quote for the wrong part. Ask for the date code and the lot code before you order, and for a certificate of conformance that names the part, the quantity, the lot, and the date code. Ask for the tray quantity and the packaging, and ask whether the STM32H753ZIT6 is available as well, so the 144 pin version sits next to the 100 pin version on the same quotation. When the change touches more than one line on the BOM, send the full list through our BOM Kitting service, so every line is checked against the same revision and the alternative is recorded with the engineer approval behind it.
What Do Buyers Ask Next?
Are the STM32F429ZIT6 and the STM32H753VIT6 pin compatible?
No. The STM32F429ZIT6 uses a 144 pin LQFP and the STM32H753VIT6 uses a 100 pin LQFP, so the footprints and the pinout differ. A board built for one will not accept the other.
Can I reuse my firmware when I move to the STM32H753VIT6?
Not directly. The core changes from a Cortex M4 to a Cortex M7, and the clock tree, memory map, and HAL change with it. Plan a port, a bench test, and an engineer review before the change goes to production.
Is the STM32H753VIT6 faster than the STM32F429ZIT6?
Yes. It runs at up to 480 MHz and delivers 1027 DMIPS, against 180 MHz and 225 DMIPS on the STM32F429ZIT6. Speed helps compute load, but it does not fix a missing pin or a bus that disagrees.
What if my board cannot change?
Ask for the STM32H753ZIT6, the 144 pin version of the same H7 part. The footprint question goes away, but the firmware, ADC, and CAN FD questions stay and still need engineer approval.
What should I do when the STM32F429ZIT6 is out of stock?
Get the engineer to approve the change first, then ask for a quotation that names the full suffix, the date code, and the lot code. Ask for both the VIT6 and the ZIT6 in the same enquiry, so the choice is made on price and availability.
Related Reading
How to Evaluate Component Alternatives
Sample BOM Example: A Filled In BOM Line by Line for Quotation
Written by Casey Xia
Casey Xia handles component sourcing enquiries at Potrgo, covering BOM quotation, shortage lines, and alternatives screening. These articles collect the checks and decisions behind that work. More about the author · Casey Xia on LinkedIn
